Antenne WIFI non reconnue / pas de hotspot


#1

Bonjour,

J’ai un souci sur ma brique. L’install se passe bien, j’ai migré vers Yunohost 3.3.
J’ai bien accès à l’admin de ma brique, malheureusement je ne vois pas le réseau wifi Hotspot.
En cherchant dans les service, celui-ci est inactif.

En me connectant sur l’interface utilisateur, j’ai le message suivant :

[ERR] Hotspot Service disabled
[INFO] Autodetected internet interface: tun0 (last start: tun0)
[ERR] No IPv4 NAT set
[ERR] No IPv6/IPv4 forwarding set
[ERR] Hostapd is not running
[INFO] hotspot0: No IPv6 delegated prefix found
[ERR] hotspot0: DHCPv4 (dnsmasq) is not running
[ERR] hotspot0: No IPv4 NAT address set

Dès que je veux l’activer, il refuse car je ne peux choisir d’interface (il n’y en a aucune de proposer pourtant mon antenne est bien connectée).

Mon antenne est une TP Link WN722N.

Quelqu’un a déjà eu ce problème ?

Merci pour vos réponses
Papsout


#2

Du coup j’imagine que c’est un problème de driver et que ton antenne n’est pas reconnue automatiquement …

(Où as-tu obtenu le matos de ta brique ?)


#3

Oui j’imagine aussi…
J’ai eu ma brique par l’asso FAIMAISON

Carte mère : A20-OLinuXino-LIME

Étrangement sur d’autres briques avec le même hardware, il n’y pas de soucis…
Mais visiblement la WN722N changerait de puce (puce Atheros remplacée par un
Realtek) dans ses dernières versions. Ce qui pourrait expliquer un problème de drivers !


#4

Si c’est un problème de driver alors ça peut vite devenir technique … je pense que l’idéal serait de voir ça de vive voix avec quelqu’un de FAI maison idéalement…

Sinon on peut tenter d’investiguer des trucs en asynchrone mais il va falloir un certain nombre d’itérations :wink:

Si ça te tente, naivement je pense qu’on commencer par regarder ce que donnent les commandes suivantes :

$ lspci
$ lsusb
$ ip a
$ dmesg

#5

les commandes lspci et lsusb ne fonctionnent pas (commandes introuvables)

pour ip a voici ce qu’il me dit :

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 02:13:0b:81:e5:64 brd ff:ff:ff:ff:ff:ff
    inet 192.168.0.48/24 brd 192.168.0.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 2a01:e35:2e3d:31b0:13:bff:fe81:e564/64 scope global mngtmpaddr dynamic 
       valid_lft 86345sec preferred_lft 86345sec
    inet6 fe80::42:babe/128 scope link 
       valid_lft forever preferred_lft forever
    inet6 fe80::13:bff:fe81:e564/64 scope link 
       valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether c0:25:e9:27:7e:ec brd ff:ff:ff:ff:ff:ff
4: tun0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN group default qlen 100
    link/none 
    inet 89.234.176.122/26 brd 89.234.176.127 scope global tun0
       valid_lft forever preferred_lft forever
    inet6 fe80::702d:afde:844d:788c/64 scope link flags 800 
       valid_lft forever preferred_lft forever

#6

Et pour dmesg :slight_smile:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.0-8-armmp (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1) ) #1 SMP Debian 4.9.130-2 (2018-10-27)
[    0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt:Machine model: Olimex A20-OLinuXino-LIME
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 16 MiB at 0x5f000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 131072
[    0.000000] free_area_init_node: node 0, pgdat c0ce2400, node_mem_map deb71000
[    0.000000]   Normal zone: 1152 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 131072 pages, LIFO batch:31
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: Using PSCI v0.1 Function IDs from DT
[    0.000000] percpu: Embedded 14 pages/cpu @deb3a000 s27596 r8192 d21556 u57344
[    0.000000] pcpu-alloc: s27596 r8192 d21556 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129920
[    0.000000] Kernel command line: console=ttyS0,115200 console=ttyS1 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:1280x720p60 root=/dev/mmcblk0p1 rootwait sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_no_mali_mem_reserve sunxi_fb_mem_reserve=0 panic=10 loglevel=6 consoleblank=0
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 472568K/524288K available (7168K kernel code, 1008K rwdata, 2216K rodata, 1024K init, 335K bss, 35336K reserved, 16384K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                   fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
                   vmalloc : 0xe0800000 - 0xff800000   ( 496 MB)
                   lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
                   pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
                   modules : 0xbf000000 - 0xbfe00000   (  14 MB)
                     .text : 0xc0008000 - 0xc0800000   (8160 kB)
                     .init : 0xc0b00000 - 0xc0c00000   (1024 kB)
                     .data : 0xc0c00000 - 0xc0cfc1dc   (1009 kB)
                      .bss : 0xc0cfe000 - 0xc0d51c4c   ( 336 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 32.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000019] Switching to timer-based delay loop, resolution 41ns
[    0.002591] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.003348] clocksource: hstimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 12741736309 ns
[    0.004011] Console: colour dummy device 80x30
[    0.004048] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000)
[    0.004063] pid_max: default: 32768 minimum: 301
[    0.004325] Security Framework initialized
[    0.004334] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.004370] AppArmor: AppArmor disabled by boot time parameter
[    0.004450] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.004458] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.005633] CPU: Testing write buffer coherency: ok
[    0.005694] ftrace: allocating 26782 entries in 79 pages
[    0.065407] /cpus/cpu@0 missing clock-frequency property
[    0.065445] /cpus/cpu@1 missing clock-frequency property
[    0.065459] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.065508] Setting up static identity map for 0x40100000 - 0x40100098
[    0.070951] EFI services will not be available.
[    0.072593] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.072747] Brought up 2 CPUs
[    0.072760] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[    0.072764] CPU: All CPU(s) started in HYP mode.
[    0.072767] CPU: Virtualization extensions available.
[    0.073878] devtmpfs: initialized
[    0.084752] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[    0.085295] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns
[    0.085321] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.086259] pinctrl core: initialized pinctrl subsystem
[    0.088367] NET: Registered protocol family 16
[    0.090548] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.093252] No ATAGs?
[    0.093294] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.093300] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.094209] Serial: AMBA PL011 UART driver
[    0.129002] reg-fixed-voltage ahci-5v: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@1, deferring probe
[    0.129056] reg-fixed-voltage usb0-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb0_vbus_pin@0, deferring probe
[    0.129087] reg-fixed-voltage usb1-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[    0.129118] reg-fixed-voltage usb2-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
[    0.132361] vgaarb: loaded
[    0.133382] media: Linux media interface: v0.10
[    0.133437] Linux video capture interface: v2.00
[    0.133520] pps_core: LinuxPPS API ver. 1 registered
[    0.133525] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.133546] PTP clock support registered
[    0.135718] clocksource: Switched to clocksource arch_sys_counter
[    0.182597] VFS: Disk quotas dquot_6.6.0
[    0.182721] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.196955] NET: Registered protocol family 2
[    0.197913] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.197965] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.198027] TCP: Hash tables configured (established 4096 bind 4096)
[    0.198096] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.198128] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.198388] NET: Registered protocol family 1
[    0.198432] PCI: CLS 0 bytes, default 64
[    0.199009] Unpacking initramfs...
[    1.502979] Freeing initrd memory: 17392K
[    1.503801] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    1.505970] audit: initializing netlink subsys (disabled)
[    1.506076] audit: type=2000 audit(1.470:1): initialized
[    1.507471] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    1.507646] zbud: loaded
[    1.511432] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    1.511642] io scheduler noop registered
[    1.511650] io scheduler deadline registered
[    1.511742] io scheduler cfq registered (default)
[    1.517555] sun7i-a20-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    1.532356] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.534710] console [ttyS0] disabled
[    1.555213] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 42, base_baud = 1500000) is a U6_16550A
[    1.676720] console [ttyS0] enabled
[    1.677611] Serial: AMBA driver
[    1.680794] libphy: Fixed MDIO Bus: probed
[    1.681693] mousedev: PS/2 mouse device common for all mice
[    1.683838] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0
[    1.683850] sunxi-rtc 1c20d00.rtc: RTC enabled
[    1.686402] ledtrig-cpu: registered to indicate activity on CPUs
[    1.687251] NET: Registered protocol family 10
[    1.688460] mip6: Mobile IPv6
[    1.688482] NET: Registered protocol family 17
[    1.688499] mpls_gso: MPLS GSO support
[    1.688740] ThumbEE CPU extension supported.
[    1.688756] Registering SWP/SWPB emulation handler
[    1.694625] registered taskstats version 1
[    1.694722] zswap: loaded using pool lzo/zbud
[    1.695043] ima: No TPM chip found, activating TPM-bypass!
[    1.695059] ima: Allocated hash algorithm: sha256
[    1.705390] sunxi-rtc 1c20d00.rtc: setting system clock to 2019-01-14 22:54:48 UTC (1547506488)
[    1.705407] sr_init: No PMIC hook to init smartreflex
[    1.710820] sr_init: platform driver register failed for SR
[    1.716733] PM: Hibernation image not present or could not be loaded.
[    1.716915] vcc3v0: disabling
[    1.716923] vcc3v3: disabling
[    1.716927] vcc5v0: disabling
[    1.716932] ahci-5v: disabling
[    1.716940] usb0-vbus: disabling
[    1.716944] usb1-vbus: disabling
[    1.716950] usb2-vbus: disabling
[    1.718572] Freeing unused kernel memory: 1024K
[    1.840566] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    1.848489] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    1.849128] random: udevadm: uninitialized urandom read (16 bytes read)
[    2.134481] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[    2.143667] usbcore: registered new interface driver usbfs
[    2.143755] usbcore: registered new interface driver hub
[    2.143948] usbcore: registered new device driver usb
[    2.154575] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.156353] ehci-platform: EHCI generic platform driver
[    2.159010] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.160657] ohci-platform: OHCI generic platform driver
[    2.172066] sunxi-mmc 1c0f000.mmc: base:0xe0917000 irq:27
[    2.175603] ehci-platform 1c14000.usb: EHCI Host Controller
[    2.175655] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[    2.176579] ehci-platform 1c14000.usb: irq 29, io mem 0x01c14000
[    2.196762] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[    2.197220] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.197231] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.197239] usb usb1: Product: EHCI Host Controller
[    2.197245] usb usb1: Manufacturer: Linux 4.9.0-8-armmp ehci_hcd
[    2.197252] usb usb1: SerialNumber: 1c14000.usb
[    2.198355] hub 1-0:1.0: USB hub found
[    2.206308] hub 1-0:1.0: 1 port detected
[    2.207387] ehci-platform 1c1c000.usb: EHCI Host Controller
[    2.207440] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[    2.220341] ehci-platform 1c1c000.usb: irq 33, io mem 0x01c1c000
[    2.228409] SCSI subsystem initialized
[    2.232357] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[    2.232727] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    2.232737] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.232745] usb usb2: Product: EHCI Host Controller
[    2.232751] usb usb2: Manufacturer: Linux 4.9.0-8-armmp ehci_hcd
[    2.232758] usb usb2: SerialNumber: 1c1c000.usb
[    2.233793] hub 2-0:1.0: USB hub found
[    2.233871] hub 2-0:1.0: 1 port detected
[    2.234803] ohci-platform 1c14400.usb: Generic Platform OHCI controller
[    2.234883] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
[    2.235410] ohci-platform 1c14400.usb: irq 30, io mem 0x01c14400
[    2.247328] mmc0: host does not support reading read-only switch, assuming write-enable
[    2.290329] mmc0: new high speed SDHC card at address 0007
[    2.295201] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    2.295217] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.295224] usb usb3: Product: Generic Platform OHCI controller
[    2.295231] usb usb3: Manufacturer: Linux 4.9.0-8-armmp ohci_hcd
[    2.295237] usb usb3: SerialNumber: 1c14400.usb
[    2.301497] hub 3-0:1.0: USB hub found
[    2.301595] hub 3-0:1.0: 1 port detected
[    2.302999] usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[    2.317254] mmcblk0: mmc0:0007 SD16G 14.5 GiB 
[    2.319906] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[    2.319929] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 4
[    2.320219] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[    2.320229] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.320236] usb usb4: Product: MUSB HDRC host driver
[    2.320243] usb usb4: Manufacturer: Linux 4.9.0-8-armmp musb-hcd
[    2.320249] usb usb4: SerialNumber: musb-hdrc.1.auto
[    2.321361]  mmcblk0: p1
[    2.324297] hub 4-0:1.0: USB hub found
[    2.324396] hub 4-0:1.0: 1 port detected
[    2.327196] axp20x-i2c 0-0034: AXP20x variant AXP209 found
[    2.327677] libata version 3.00 loaded.
[    2.339335] axp20x-i2c 0-0034: AXP20X driver loaded
[    2.341148] sun7i-dwmac 1c50000.ethernet: no regulator found
[    2.341285] sun7i-dwmac 1c50000.ethernet: no reset control found
[    2.341294]  Ring mode enabled
[    2.341299]  DMA HW capability register supported
[    2.341305]  Normal descriptors
[    2.355137] libphy: stmmac: probed
[    2.355158] eth%d: PHY ID 00008201 at 1 IRQ POLL (stmmac-0:01) active
[    2.359078] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[    2.359137] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 5
[    2.359609] ohci-platform 1c1c400.usb: irq 34, io mem 0x01c1c400
[    2.420463] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    2.420478] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.420486] usb usb5: Product: Generic Platform OHCI controller
[    2.420492] usb usb5: Manufacturer: Linux 4.9.0-8-armmp ohci_hcd
[    2.420499] usb usb5: SerialNumber: 1c1c400.usb
[    2.421786] hub 5-0:1.0: USB hub found
[    2.421870] hub 5-0:1.0: 1 port detected
[    2.476703] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[    2.476725] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[    2.483898] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    2.483917] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc 
[    2.485800] scsi host0: ahci-sunxi
[    2.486379] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 32
[    2.503789] axp20x-regulator axp20x-regulator: regulators node not found
[    2.540850] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    2.691645] usb 1-1: New USB device found, idVendor=2357, idProduct=010c
[    2.691661] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.691668] usb 1-1: Product: 802.11n NIC
[    2.691674] usb 1-1: Manufacturer: Realtek
[    2.691680] usb 1-1: SerialNumber: 00E04C0001
[    2.704992] random: fast init done
[    2.802395] ata1: SATA link down (SStatus 0 SControl 300)
[    3.081904] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
[    3.876253] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.920507] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[    3.921464] systemd[1]: Detected architecture arm.
[    3.937451] systemd[1]: Set hostname to <papsout.nohost.me>.
[    4.096421] systemd-fstab-generator[138]: Failed to create mount unit file /run/systemd/generator/-.mount, as it already exists. Duplicate entry in /etc/fstab?
[    4.111347] systemd-fstab-generator[138]: Failed to create mount unit file /run/systemd/generator/-.mount, as it already exists. Duplicate entry in /etc/fstab?
[    4.126007] systemd-fstab-generator[138]: Failed to create mount unit file /run/systemd/generator/-.mount, as it already exists. Duplicate entry in /etc/fstab?
[    4.140695] systemd-fstab-generator[138]: Failed to create mount unit file /run/systemd/generator/-.mount, as it already exists. Duplicate entry in /etc/fstab?
[    4.155311] systemd-fstab-generator[138]: Failed to create mount unit file /run/systemd/generator/-.mount, as it already exists. Duplicate entry in /etc/fstab?
[    4.655345] systemd[132]: /lib/systemd/system-generators/systemd-fstab-generator failed with error code 1.
[    4.980629] systemd[1]: Listening on udev Kernel Socket.
[    4.996403] systemd[1]: Listening on Journal Socket (/dev/log).
[    5.012203] systemd[1]: Created slice System Slice.
[    5.030454] systemd[1]: Mounting Debug File System...
[    5.046983] systemd[1]: Reached target Swap.
[    5.061663] systemd[1]: Listening on Journal Socket.
[    5.548387] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[    5.548511] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[    5.549667] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[    5.568375] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[    5.571383] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[    5.571915] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[    5.899748] systemd-journald[168]: Received request to flush runtime journal from PID 1
[    7.341431] random: crng init done
[    7.344865] random: 7 urandom warning(s) missed due to ratelimiting
[    7.602483] sun4i-ss 1c15000.crypto-engine: no reset control found
[    7.604123] sun4i-ss 1c15000.crypto-engine: Die ID 0
[    7.725681] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    7.830174] at24 1-0050: 2048 byte 24c16 EEPROM, writable, 16 bytes/write
[    7.834691] input: axp20x-pek as /devices/platform/soc@01c00000/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input0
[    7.949811] r8188eu: module is from the staging directory, the quality is unknown, you have been warned.
[    8.025952] Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_D_CUT_1T1R_RomVer(0)
[    8.096186] usbcore: registered new interface driver r8188eu
[   10.462274]  RX IPC Checksum Offload disabled
[   10.466695]  No MAC Management Counters available
[   10.466716] sun7i-dwmac 1c50000.ethernet eth0: fail to init PTP.
[   10.478719] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   11.511002] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[   11.511051] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   36.416331] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[   38.590619] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   80.232214] tun: Universal TUN/TAP device driver, 1.6
[   80.232230] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>

#7

Ebeennnn visiblement mon intuition était mauvaise : il y a bien une interface wifi apriori :

$ ip a
[...]
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 
    link/ether c0:25:e9:27:7e:ec brd ff:ff:ff:ff:ff:ff
[...]

Du coup elle n’est “seulement” pas active…

Est-ce que tu saurais aller sur le SSO pour accéder à l’inteface de configuration du Wifi Hotspot, regarder si tout les reglages ont l’air de faire sens, puis juste faire “Save & Reload” ?


#8

Sur la page du Wifi Hotspot, il m’indique que le service est éteint.
Et dans les détails :
[ERR] Hotspot Service disabled
[INFO] Autodetected internet interface: tun0 (last start: tun0)
[ERR] No IPv4 NAT set
[ERR] No IPv6/IPv4 forwarding set
[ERR] Hostapd is not running
[INFO] hotspot0: No IPv6 delegated prefix found
[ERR] hotspot0: DHCPv4 (dnsmasq) is not running
[ERR] hotspot0: No IPv4 NAT address set

Lorsque je souhaite passer sur “on” le point d’accès activé et ensuite faire un save and reload, il refuse ( Erreur: Vous devez choisir une interface d’antenne WiFi (configuration non-mise à jour). car je ne peux pas choisir d’antenne dans la rubrique “interface”.


#9

Finalement j’ai acheté un nouveau modèle d’antenne (celui qui était recommandé):

Et ça fonctionne très bien ! Merci pour ton aide Aleks